Slackware 13.0slackware-13.0

Wed Aug 26 10:00:38 CDT 2009
Slackware 13.0 x86_64 is released as stable!  Thanks to everyone who
helped make this release possible -- see the RELEASE_NOTES for the
credits.  The ISOs are off to the replicator.  This time it will be a
6 CD-ROM 32-bit set and a dual-sided 32-bit/64-bit x86/x86_64 DVD.
We're taking pre-orders now at store.slackware.com.  Please consider
picking up a copy to help support the project.  Once again, thanks to
the entire Slackware community for all the help testing and fixing
things and offering suggestions during this development cycle.
As always, have fun and enjoy!  -P.

1 files changed, 202 insertions, 0 deletions

diff --git a/source/n/network-scripts/manpages/rc.inet1.conf.5 b/source/n/network-scripts/manpages/rc.inet1.conf.5
new file mode 100644
index 00000000..b23f6783
--- /dev/null
+++ b/source/n/network-scripts/manpages/rc.inet1.conf.5
@@ -0,0 +1,202 @@
+.\" -*- nroff -*-
+.ds g \" empty
+.ds G \" empty
+.\" Like TP, but if specified indent is more than half
+.\" the current line-length - indent, use the default indent.
+.de Tp
+.ie \\n(.$=0:((0\\$1)*2u>(\\n(.lu-\\n(.iu)) .TP
+.el .TP "\\$1"
+..
+.TH RC.INET1.CONF 5 "03 Dec 2008" "Slackware Version 12.2.0"
+.SH NAME
+rc.inet1.conf \- Slackware network configuration file.
+.SH DESCRIPTION
+.B rc.inet1.conf
+\. This file contains the configuration settings for network interfaces.
+It consists basically of a series of variable array definitions.
+Array elements with the same index number will all belong to the same
+network interface.
+.LP
+By default, index number `0' is used for the configuration of interface
+.I eth0,
+index number `1' is used for
+.I eth1
+and so forth. The default interface name can be overruled by the use of
+the variable
+.B IFNAME.
+.LP
+This is what a typical section of the file looks like for a card that is
+configured to use DHCP, showing all array variables with the index number [0]:
+.LP
+# Config information for eth0:
+.br
+IPADDR[0]=""
+.br
+NETMASK[0]=""
+.br
+USE_DHCP[0]="yes"
+.br
+DHCP_HOSTNAME[0]=""
+.br
+DHCP_TIMEOUT[0]=""
+.LP
+Alternatively, here is an example for a card that uses a static IP address and
+has a non-default name (
+.I ath0
+instead of
+.I eth1
+). The array index is [1] in this case.
+.LP
+# Config information for ath0 (using static IP address):
+.br
+IFNAME[1]="ath0"
+.br
+IPADDR[1]="192.168.3.11"
+.br
+NETMASK[1]="255.255.255.0"
+.br
+USE_DHCP[1]=""
+.br
+DHCP_HOSTNAME[1]=""
+.br
+GATEWAY="192.168.3.1"
+.SH GENERAL PARAMETERS
+This is a list of network parameters you can set for any card (wired as well
+as wired).  The example section is for `eth0' by default, i.e.
+the array variables all have the array index [0]:
+.LP
+# Config information for eth0:
+.TP 25
+IPADDR[0]=""
+# Set this value to an actual IP address if you want static IP
+address assignment
+.TP
+NETMASK[0]=""
+# With a static IP address, you are required to also set a netmask
+(255.255.255.0 is common)
+.TP
+USE_DHCP[0]="yes"
+# If set to "yes", we will run a DHCP client and have the IP address
+dynamically assigned
+.TP
+DHCP_HOSTNAME[0]="mybox"
+# Tell the DHCP server what hostname to register
+.TP
+DHCP_TIMEOUT[0]=15
+# The default timeout for the DHCP client to wait for server response is
+30 seconds, but you might want a shorter wait.
+.TP
+IFNAME[0]="eth0:1"
+# Set up an IP alias.
+.TP
+HWADDR[0]="00:01:23:45:67:89"
+# Overrule the card's hardware MAC address
+.TP
+MTU[0]=""
+# The default MTU is 1500, but you might need 1360 when you use NAT'ed
+IPSec traffic.
+.TP
+DHCP_KEEPRESOLV[0]="yes"
+# If you do
+.B not
+want `/etc/resolv.conf' overwritten by the DHCP client
+.TP
+DHCP_KEEPNTP[0]="yes"
+# If you do
+.B not
+want `/etc/ntp.conf' overwritten by the DHCP client
+.TP
+DHCP_KEEPGW[0]="yes"
+# If you do
+.B not
+want the DHCP client to change your default gateway
+.TP
+DHCP_DEBUG[0]="yes"
+# Make dhcpcd show verbose diagnostics
+.TP
+DHCP_NOIPV4LL[0]="yes"
+# Do not assign an
+.I `ipv4ll'
+address when a DHCP server is not found (ipv4 link-local addressing in the IP range 169.254.0.0/16 is also known as
+.I `zeroconf'
+address assignment)
+.TP
+DHCP_IPADDR[0]=""
+# Request a specific IP address from the DHCP server
+.SH WIRELESS PARAMETERS
+For wireless cards, several additional parameter definitions are available.
+All these parameters (or better, variables) start with the prefix
+.B WLAN_ .
+.LP
+.TP 25
+WLAN_ESSID[4]=DARKSTAR
+# Your Wireless Access Point's name
+.TP
+WLAN_MODE[4]=Managed
+# "Managed" mode for use with Access Points.  "Ad-Hoc" is for
+peer-to-peer connections.
+.TP
+WLAN_RATE[4]="54M auto"
+# The transmission rates you want the driver to try ("auto" means
+that bandwidth can be variable)
+.TP
+WLAN_CHANNEL[4]="auto"
+# The channel to which the Access Point is tuned ("auto" to let the
+driver find out the correct channel) 
+.TP
+WLAN_KEY[4]="D5A31F54ACF0487C2D0B1C10D2"
+# Definition of a WEP key
+.TP
+WLAN_IWPRIV[4]="set AuthMode=WPAPSK | set EncrypType=TKIP | set WPAPSK=the_64_character_key"
+# Some drivers require a private ioctl to be set through the iwpriv command.
+If more than one is required, you can place them in the
+.I IWPRIV
+parameter (separated with the pipe (|) character, see the example).
+.TP 
+WLAN_WPA[4]="wpa_supplicant"
+# Run wpa_supplicant for WPA support
+.TP
+WLAN_WPADRIVER[4]="ndiswrapper"
+# Tell wpa_supplicant to specifically use the ndiswrapper driver.
+If you leave this empty the `wext' driver is used by default; most
+modern wireless drivers use 'wext'.
+.TP
+WLAN_WPAWAIT[4]=30
+# In case it takes long for the WPA association to finish, you can
+increase the wait time before rc.wireless decides that association
+failed (defaults to 10 seconds)
+.SH FILES
+.TP 25
+.I /etc/rc.d/rc.inet1
+network configuration script
+.TP
+.I /etc/rc.d/rc.inet1.conf
+configuration parameter file (is being read by rc.inet1 andrc.wireless)
+.TP
+.I /etc/rc.d/rc.wireless
+wireless configuration script
+.TP
+.I /etc/rc.d/rc.wireless.conf
+configuration parameter file (
+.B deprecated
+)
+.SH CAVEATS
+The network interface definitions are stored in variable
+.I arrays.
+The bash shell has no facilities to retrieve the largest array index used.
+Therefore, the
+.I rc.inet1
+script makes the assumption that array indexes stay below the value of
+.B 6
+\.
+.LP
+If you want to configure more than six network interfaces, you will
+have to edit the file
+.I /etc/rc.d/rc.inet1
+and change the value `6' in the line
+.B MAXNICS=${MAXNICS:-6}
+to the number of network interfaces you wish to use.
+.SH AUTHOR
+Eric Hameleers <alien@slackware.com>
+.SH "SEE ALSO"
+.BR rc.inet1(8)