Wed Jun 6 22:19:01 UTC 201820180606221901

a/bash-4.4.023-x86_64-1.txz:  Upgraded.
a/kernel-firmware-20180604_1fa9ce3-noarch-1.txz:  Upgraded.
a/kernel-generic-4.14.48-x86_64-1.txz:  Upgraded.
a/kernel-huge-4.14.48-x86_64-1.txz:  Upgraded.
a/kernel-modules-4.14.48-x86_64-1.txz:  Upgraded.
ap/cups-2.2.8-x86_64-1.txz:  Upgraded.
ap/ghostscript-fonts-std-8.11-noarch-3.txz:  Rebuilt.
  Rebuilt this and many other font packages or packages with build scripts
  that call mkfontdir or mkfontscale to suppress any error messages caused
  by collisions if another package installation is writing files to the
  same font directories when those utilities are run. In that case, the
  other package will also be running mkfontdir/mkfontscale after the files
  are installed, so any issues will be cleaned up then. Last one out turn
  off the lights, so to speak.
ap/sqlite-3.24.0-x86_64-1.txz:  Upgraded.
ap/terminus-font-4.40-noarch-3.txz:  Rebuilt.
d/kernel-headers-4.14.48-x86-1.txz:  Upgraded.
d/rust-1.26.2-x86_64-1.txz:  Upgraded.
k/kernel-source-4.14.48-noarch-1.txz:  Upgraded.
l/elfutils-0.171-x86_64-1.txz:  Upgraded.
l/harfbuzz-1.7.7-x86_64-1.txz:  Upgraded.
l/mozilla-nss-3.37.3-x86_64-1.txz:  Upgraded.
l/readline-7.0.005-x86_64-1.txz:  Upgraded.
x/dejavu-fonts-ttf-2.37-noarch-4.txz:  Rebuilt.
x/font-adobe-100dpi-1.0.3-noarch-3.txz:  Rebuilt.
x/font-adobe-75dpi-1.0.3-noarch-3.txz:  Rebuilt.
x/font-adobe-utopia-100dpi-1.0.4-noarch-3.txz:  Rebuilt.
x/font-adobe-utopia-75dpi-1.0.4-noarch-3.txz:  Rebuilt.
x/font-adobe-utopia-type1-1.0.4-noarch-3.txz:  Rebuilt.
x/font-arabic-misc-1.0.3-noarch-3.txz:  Rebuilt.
x/font-bh-100dpi-1.0.3-noarch-3.txz:  Rebuilt.
x/font-bh-75dpi-1.0.3-noarch-3.txz:  Rebuilt.
x/font-bh-lucidatypewriter-100dpi-1.0.3-noarch-3.txz:  Rebuilt.
x/font-bh-lucidatypewriter-75dpi-1.0.3-noarch-3.txz:  Rebuilt.
x/font-bh-ttf-1.0.3-noarch-3.txz:  Rebuilt.
x/font-bh-type1-1.0.3-noarch-3.txz:  Rebuilt.
x/font-bitstream-100dpi-1.0.3-noarch-3.txz:  Rebuilt.
x/font-bitstream-75dpi-1.0.3-noarch-3.txz:  Rebuilt.
x/font-bitstream-speedo-1.0.2-noarch-3.txz:  Rebuilt.
x/font-bitstream-type1-1.0.3-noarch-3.txz:  Rebuilt.
x/font-cronyx-cyrillic-1.0.3-noarch-3.txz:  Rebuilt.
x/font-cursor-misc-1.0.3-noarch-3.txz:  Rebuilt.
x/font-daewoo-misc-1.0.3-noarch-3.txz:  Rebuilt.
x/font-dec-misc-1.0.3-noarch-3.txz:  Rebuilt.
x/font-ibm-type1-1.0.3-noarch-3.txz:  Rebuilt.
x/font-isas-misc-1.0.3-noarch-3.txz:  Rebuilt.
x/font-jis-misc-1.0.3-noarch-3.txz:  Rebuilt.
x/font-micro-misc-1.0.3-noarch-3.txz:  Rebuilt.
x/font-misc-cyrillic-1.0.3-noarch-3.txz:  Rebuilt.
x/font-misc-ethiopic-1.0.3-noarch-3.txz:  Rebuilt.
x/font-misc-meltho-1.0.3-noarch-3.txz:  Rebuilt.
x/font-misc-misc-1.1.2-noarch-3.txz:  Rebuilt.
x/font-mutt-misc-1.0.3-noarch-3.txz:  Rebuilt.
x/font-schumacher-misc-1.1.2-noarch-3.txz:  Rebuilt.
x/font-screen-cyrillic-1.0.4-noarch-3.txz:  Rebuilt.
x/font-sony-misc-1.0.3-noarch-3.txz:  Rebuilt.
x/font-sun-misc-1.0.3-noarch-3.txz:  Rebuilt.
x/font-winitzki-cyrillic-1.0.3-noarch-3.txz:  Rebuilt.
x/font-xfree86-type1-1.0.4-noarch-3.txz:  Rebuilt.
x/liberation-fonts-ttf-2.00.1-noarch-3.txz:  Rebuilt.
x/libinput-1.11.0-x86_64-1.txz:  Upgraded.
x/sazanami-fonts-ttf-20040629-noarch-3.txz:  Rebuilt.
x/sinhala_lklug-font-ttf-20060929-noarch-3.txz:  Rebuilt.
x/tibmachuni-font-ttf-1.901b-noarch-3.txz:  Rebuilt.
x/ttf-indic-fonts-0.5.14-noarch-3.txz:  Rebuilt.
x/ttf-tlwg-0.6.4-noarch-3.txz:  Rebuilt.
x/urw-core35-fonts-otf-20170801_91edd6e_git-noarch-2.txz:  Rebuilt.
x/wqy-zenhei-font-ttf-0.8.38_1-noarch-6.txz:  Rebuilt.
xap/mozilla-firefox-60.0.2-x86_64-1.txz:  Upgraded.
  This release contains security fixes and improvements.
  For more information, see:
    https://www.mozilla.org/security/known-vulnerabilities/firefox.html
  (* Security fix *)
xap/x3270-3.3.12ga7-x86_64-5.txz:  Rebuilt.
isolinux/initrd.img:  Rebuilt.
kernels/*:  Upgraded.
usb-and-pxe-installers/usbboot.img:  Rebuilt.

1 files changed, 250 insertions, 0 deletions

diff --git a/source/installer/sources/initrd/etc/rc.d/rc.S b/source/installer/sources/initrd/etc/rc.d/rc.S
new file mode 100755
index 00000000..38317b4d
--- /dev/null
+++ b/source/installer/sources/initrd/etc/rc.d/rc.S
@@ -0,0 +1,250 @@
+#!/bin/sh
+# rc.S: Basic system initialization.
+
+# Any /etc/mtab that exists here is old, so we start with a new one:
+/bin/rm -f /etc/mtab{,~,.tmp} && /bin/touch /etc/mtab
+
+# Add (fake) entry for / to /etc/mtab:
+/sbin/mount -f -w /dev/initramfs / -t tmpfs 1> /dev/null
+
+# Mount /proc:
+/sbin/mount -v proc /proc -t proc 1> /dev/null
+
+# Mount sysfs next:
+/sbin/mount -v sysfs /sys -t sysfs 1> /dev/null
+
+# Activate swap:
+/sbin/swapon -a 1> /dev/null
+
+if [ -x /sbin/ldconfig ]; then
+  /sbin/ldconfig 1> /dev/null
+fi
+
+## Detect serial console from kernel command line:
+#if cat /proc/cmdline | grep console=ttyS 1> /dev/null 2> /dev/null ; then
+#  SERIAL_CONSOLE="true"
+#fi
+
+# System logger (mostly to eat annoying messages):
+/sbin/syslogd 2> /dev/null
+sleep 1
+/sbin/klogd -c 3 1> /dev/null
+
+# Try to load the loop module:
+modprobe loop 1> /dev/null 2> /dev/null
+
+# Run udev:
+if ! grep -wq noudev /proc/cmdline ; then
+  /bin/bash /etc/rc.d/rc.udev start
+
+  # Re-assemble RAID volumes:
+  /sbin/mdadm -E -s > /etc/mdadm.conf
+  /sbin/mdadm -S -s
+  /sbin/mdadm -A -s
+  # This seems to make the kernel see partitions more reliably:
+  fdisk -l /dev/md* 1> /dev/null 2> /dev/null
+else
+  # Run our old detection routines:
+
+  # Look for USB keyboard or storage:
+  /etc/rc.d/rc.usb start
+  sleep 3
+
+  # Look for IEEE1394 devices:
+  if grep 1394 /proc/pci 1> /dev/null 2> /dev/null ; then
+    /etc/rc.d/rc.ieee1394 start
+    #sleep 3
+  fi
+
+  # Load additional install floppies:
+  for NEWDISK in 2 ; do
+    if [ ! -r /etc/disk${NEWDISK} ]; then
+      while [ 0 ]; do
+        echo
+        echo -n "Insert install.${NEWDISK} floppy disk to be loaded into RAM disk and press ENTER"
+        read readfoo;
+        if [ "$readfoo" = "Q" -o "$readfoo" = "q" ]; then
+          break;
+        fi
+        echo -n "Loading install.${NEWDISK} floppy into RAM disk...  "
+        ( cd / ; cat /dev/fd0 | zcat 2> /dev/null | tar xf - )
+        if [ -r /etc/disk${NEWDISK} ]; then
+          echo "done."
+          echo
+          break;
+        else
+          echo "Error. (reload or enter Q)"
+          echo
+          continue;
+        fi
+      done
+    fi
+  done
+
+  ### PROBABLY USELESS WITHOUT SOME TIMED DELAY ABOVE
+  ## Start USB again (in case we missed a USB keyboard)
+  #/etc/rc.d/rc.usb start
+
+  # Make detected partitions:
+  /dev/makedevs.sh
+
+  ## Not needed with CONFIG_SCSI_MULTI_LUN=y
+  #unset SCAN
+  ## Now we should rescan the "SCSI" bus to look for new USB or firewire devices
+  ## that look like SCSI devices:
+  #if [ -r /proc/bus/usb/devices ]; then
+  #  if cat /proc/bus/usb/devices | grep -w usb-storage 1> /dev/null 2> /dev/null ; then
+  #    SCAN="true"
+  #  fi
+  #fi
+  #if [ -r /proc/bus/ieee1394/devices ]; then
+  #  if cat /proc/bus/ieee1394/devices | grep -w SBP2 1> /dev/null 2> /dev/null ; then
+  #    SCAN="true"
+  #  fi
+  #fi
+  #if [ "$SCAN" = "true" ]; then
+  #  if ! cat /proc/cmdline | grep -q noscanluns 2> /dev/null ; then
+  #    echo "Detected new USB/IEEE1394 storage devices...  scanning all LUNs."
+  #    echo "(to skip, give a 'noscanluns' kernel option at boot)"  
+  #    #sleep 5
+  #    sh /sbin/rescan-scsi-bus -l
+  #    #sleep 1
+  #  fi
+  #fi
+  #unset SCAN
+
+  # Re-assemble RAID volumes:
+  /sbin/mdadm -E -s > /etc/mdadm.conf
+  /sbin/mdadm -S -s
+  /sbin/mdadm -A -s
+  # This seems to make the kernel see partitions more reliably:
+  fdisk -l /dev/md* 1> /dev/null 2> /dev/null
+
+  # Check /proc/partitions again:
+  /dev/makedevs.sh
+
+  # Create LVM nodes:
+  /dev/devmap_mknod.sh
+
+fi # End Run udev:
+
+# Here's the situation. Because of the practice of keeping the local
+# time (rather than UTC) in the system's clock, at any given time half
+# of the people doing an install will be creating files that upon
+# reboot will appear to have been created in the future.
+#
+# There are a lot of things that aren't happy when that happens. The
+# one that screams the most loudly is e2fsck, and we don't want to
+# anger that! Sometimes it even proceeds to check the partitions just
+# to be sure the user is fully punished.
+#
+# But, there's a simple solution. If we set the (temporary) Linux clock
+# to yesterday (-24h), then there's no way that could occur. Everything
+# on the system will be in the past (but not too far in the past).
+# Since files will quickly be put into use and given the correct after
+# reboot, this really shouldn't have a negative impact. Plus, it affects
+# only newly created files during installation -- any file shipped in a
+# package will have an accurate time of creation. (for its timezone ;-)
+#
+# Update: We have to use 2 days ago, or chroot()+timezone offset might
+# still be in the future... <sigh>
+#
+touch /.today
+/bin/sh /sbin/fakedate
+
+if [ -x /etc/rc.d/rc.inet1 ]; then
+  /bin/sh /etc/rc.d/rc.inet1
+fi
+
+# pcmciautils is installing rc.pcmcia as chmod 644, so we'll change that.
+# It won't be run at boot time, but it'll make it easy for the pcmcia script
+# or to run it from the command line.
+chmod 755 /etc/rc.d/rc.pcmcia
+
+# Scan for existing LVM partitions:
+# We will run 'vgscan -ay' in the setup to prevent a 10 second sleep;
+vgscan --mknodes 2> /tmp/foo
+cat /tmp/foo | uniq
+rm -f /tmp/foo
+
+if [ -x /etc/rc.d/rc.font ]; then
+  /bin/sh /etc/rc.d/rc.font
+fi
+
+# Don't automatically blank the screen, or it will go black during the install
+# process when stray keystrokes might be dangerous:
+/bin/setterm -blank 0
+
+echo > /etc/motd
+echo "`/bin/uname -a | /bin/cut -d\  -f1,3`." >> /etc/motd
+echo >> /etc/motd
+cat << EOF >> /etc/motd
+If you're upgrading an existing Slackware system, you might want to
+remove old packages before you run 'setup' to install the new ones. If
+you don't, your system will still work but there might be some old files
+left laying around on your drive.
+
+Just mount your Linux partitions under /mnt and type 'pkgtool'. If you
+don't know how to mount your partitions, type 'pkgtool' and it will tell
+you how it's done.
+
+To partition your hard drive(s), use 'cfdisk' or 'fdisk'.
+To start the main installation (after partitioning), type 'setup'.
+
+EOF
+
+# Dropbear seems to handle the $PATH correctly now...
+#echo > /etc/motd.net
+#echo "First command to run is 'source /etc/profile'." >> /etc/motd.net
+#echo "This will setup the PATH for you." >> /etc/motd.net
+#echo >> /etc/motd.net
+
+# If possible, figure out what kernel we just booted with:
+unset SLACK_KERNEL
+for ARG in `cat /proc/cmdline` ; do
+  if [ "`echo $ARG | cut -f 1 -d =`" = "SLACK_KERNEL" ]; then
+    IMAGE="`echo $ARG | cut -f 2 -d =`"
+    SLACK_KERNEL=$IMAGE
+  fi 
+done
+export SLACK_KERNEL
+
+. /etc/profile
+
+clear
+if ! cat /proc/cmdline | grep -q 'kbd=' 2> /dev/null ; then
+  echo
+  echo
+  echo "<OPTION TO LOAD SUPPORT FOR NON-US KEYBOARD>"
+  echo
+  echo "If you are not using a US keyboard, you may now load a different"
+  echo "keyboard map. To select a different keyboard map, please enter 1"
+  echo "now. To continue using the US map, just hit enter."
+  echo
+  echo -n "Enter 1 to select a keyboard map: "
+  read ONE
+  if [ "$ONE" = "1" ]; then
+    /usr/lib/setup/SeTkeymap
+  fi
+else
+  for ARG in `cat /proc/cmdline` ; do
+    if [ "`echo $ARG | cut -f1 -d=`" = "kbd" ]; then
+      BMAP="`echo $ARG | cut -f2 -d=`.bmap"
+    fi 
+  done
+  tar xzOf /etc/keymaps.tar.gz $BMAP | loadkmap
+  unset BMAP
+fi
+clear
+
+# Provision for unattended network configuration:
+/usr/lib/setup/SeTnet boot
+# Start dropbear ssh server (only if a configured interface is present):
+/etc/rc.d/rc.dropbear start
+
+# Fake login:  (fooled ya! ;^)
+
+cat /etc/issue
+echo -n "slackware login: "
+read BOGUS_LOGIN
+cat /etc/motd